💎 How To Format And Scan Superbox Decoder

How To Format And Scan Superbox Decoder To format and scan channels on a SuperBox decoder, you typically need to access the settings menu using the remote control. Here's a general guide on how to do it: 1. **Power On the Decoder:** - Make sure your SuperBox decoder is powered on and connected to your TV or monitor. 2. **Access the Settings Menu:** - Using the remote control, navigate to the settings menu. This is usually done by pressing the "Menu" button or a similar button labeled with a gear or settings icon. 3. **Navigate to Channel Setup:** - Once you're in the settings menu, navigate to the section related to channel setup or channel management. This might be labeled as "Channel Setup," "Channel Search," "Installation," or something similar. 4. **Format the Decoder (Optional):** - Some SuperBox decoders may have an option to format or reset the device to its factory settings. If you want to perform a complete reset, look for an option like "Factory Reset," "Format," or "Initialize." Keep in mind that formatting the decoder will erase all saved settings and channels, so proceed with caution. 5. **Scan for Channels:** - After accessing the channel setup menu, look for an option to scan for channels. This might be labeled as "Channel Search," "Auto Scan," "Auto Tune," or something similar. - Select the appropriate scanning method based on your location and the type of channels you want to scan for (terrestrial, satellite, cable, etc.). - Start the channel scan and allow the decoder to search for available channels. This process may take several minutes, depending on the speed of your decoder and the number of channels available in your area. 6. **Save Channels (If Necessary):** - Once the channel scan is complete, the decoder should display a list of detected channels. You may have the option to save all channels found or select specific channels to save. - Follow the on-screen instructions to save the scanned channels to your decoder's memory. 7. **Exit the Settings Menu:** - After completing the channel scan and saving channels (if necessary), you can exit the settings menu by pressing the "Exit" or "Back" button on the remote control. This will return you to the normal viewing interface. 8. **Verify Channel Scan Results:** - Navigate through the channels to verify that the scan was successful and that you can access all the channels you want to watch. If you encounter any difficulties during the process or if specific instructions are required for your SuperBox decoder model, refer to the user manual provided with your decoder or contact the manufacturer's customer support for assistance. __________________________________ LINKS WEBSITE: https://www.pbteck.com INSTAGRAM; https://www.instagram.com/pbtecknology/ FACEBOOK; https://www.facebook.com/pbtecknology TWITTER https://twitter.com/Pbtecknology TELEGRAM: https://t.me/pbtecknology #pbteckinfo #lnb #gotvinstallation #multitv #dishtv #directtv #dstv #satellitetv #dish #satellitedish #satellitereceiver #pbteck #pbtecknology #canalsat #canal+ #freefire

[Music] all right so welcome to Pbteck and in this video I'm going to show you how you can actually format your super box decoder so maybe there is some unstable Channel or you like to get a new settings on your decoder all you got to do is to actually format the decoder to get a fresh setting on your super box decoder all you got to do is to pick up your remote and you press on the men button on the remote and use the arrow keys just to look for settings from the menu here so you find sett

ings and then you press okay on it so from the settings page you come down to factory reset and you press okay on the factory reset so here all you have to do is to select the restore or or the first option over here and you press okay on it so here have to confirm with the default password on your superbox decoder every new FTA decoder have a default password of 4 Z so you type in 0 0 if no one have ever changed supposed to be the 4 Z so your key in 0 0 to proceed and you need to wait for

it to complete formatting and here you are everything is gone and you are having a fresh setting on your decoder now left with you to do the necessary settings or scanning to get back your channels so all you got to do if you are having a satellite channels working on your decoder all you have to do is to press on the exit button and you press on the menu button and here you come [Music] to the installation come to the menu you put it on installation and you press okay on it you need to co

nfirm with a default password once again which is the 4 zeros and you come to the antenna setting if you were having the digital or antenna channels you need to select the dvb t2 over here and then you select a country folder and you run an auto search you press okay on the auto search and don't digit Channel since you are having a stable antenna signal it's going to come over it and if you are having SL channels on it all you got to do is to select the channel type to be the S2 and then yo

u come to the antenna settings select your right satellite wherever you want to use it to scan can select any satellite at all let's select it his pass set and you count to the transponder you select the right transponder whever you are having a stable signal from it if you can't find any transponder which you are having a signal on it or you got to do to select the transponder option you press okay on it and you need to add and on this page you need to select the satellite that you are try

ing to add the transponder in it which for you to select the satellite or have the satellite menu open you need to press on the stop button on the remote for the site menu to open up and then you place it on the his Passat that we selected all right so this light right there and then you ear by pressing on the red button on the remote you add the transponder where you are having a stable signal from 125 to 25 which is the multitv frequency and then rate 30,000 vertical you highlight it and

you can proceed to scan on this page but on this page you are only limited to the brand the manual scan options so you need a brand scan to get enough of the channels available on the satellite or the platform so you need to go back to the antenna settings page on again and then you perform the brand scan over there so here you have to select the satellite whereby you have ADD the transponder which you are having a signal a quality signal from the satellite dish so you select the satellite

and then you put it on the Transformer that you add and as you can see you have the signal quality showing if the signal quality is not showing you connect your cable wall and the next thing is to press on the blue button on the remote just to perform the brand scan option and come to the scan type change it to Brand the channel type you can select FTA only to eliminate all those CR channels that comes along with the dollar dollar sign or you can just place it on all to get all channels on

your decoder the next thing is to press okay to proceed and you wait for it to complete scanning to get access to the channels that will come along after it's done scanning so if this video has been helpful and and you when are new here all you have to do subscribe hit the Bell icon and you keep coming back for more thanks for [Music] watching Street [Music] only I'm getting stronger step by step the clock is sticking time for I've been F [Music] around Soul we are heroes tonight we will f

ly above the sky we are heroes toight yeah we are heroes Tonight We Will Fly Above the we are heroes [Music] to yeah feel like aite ready to explore right up in I [Music] you I've been all around the trying to protect your soul we are heroes tonight we will fly above the sky we are heroes [Music] toight yeah we are heroes tonight we will fly above the sky we are heroes toight hey [Music] yeah we are here [Music] you

💎 How To Format And Scan Superbox Decoder

Related articles

Comments